Default Router IP Login: 192.168.1.253
It is a reserved IP address for modems or wireless routers. Most commonly, companies with the names D-link, Netgear, or TP-liNK use 192.168.1.253. You can access your router’s admin panel by typing 192.168.1.253 (NOT 192.168.o.1) in your browser’s address bar.
Default Gateway IP is another name for this type of standard IP. However, it is not the only router standard IP. Numerous other IP addresses, such as 192.168.1.1, 192.168.2.1, or 192.168.1.254, were used to access the management panel of your wireless router, Cable Gateway, or DSL Wireless Router.
Few individuals are familiar with their router’s IP address because 192.168.1.253 is typically only required in one specific circumstance. This is happening as a professional completes the setup process. As a result, you never communicate with 192.168.1.253. However, there are instances when you want to modify the WiFi network name (SSID), WiFi password, or parental controls. The IP 192.168.1.253 is then required. In addition, you may regulate data traffic, view statistics, and set up the router settings in the navigation panel after logging into your router.
Where is the 192.168.1.253 login page?
- 192.168.1.253 You can access the login page for your admin panel by entering http://192.168.1.253 into your browser.
- Login page at 192.168.1.253
- You may reset the modem to factory defaults if unsure of your password or run into an erroneous password match.
- The default username and password for 192.168.1.253
Changing the 192.168.1.253 password
Resetting your modem is all that is required. You may easily accomplish this by pressing the reset button on the bottom or back of your modem. Your modem will return to factory settings if you press and hold this tiny button for about 20 seconds (you might need a toothpick for this).
Reset the 192.168.1.253 router
You should be aware that resetting your modem will lose your internet connection. Therefore, it is preferable to seek an expert’s advice in this area. If you don’t have enough knowledge, we advise you to get assistance from a knowledgeable person.
Default login credentials for devices with 192.168.1.253 as their primary IP address
The most popular default usernames and passwords for the device IP 192.168.1.253 are displayed in this list.
Top References & FAQ – 192.168.1.253
192.168.1.253 Admin Login – Clean CSS
Enter the IP 192.168.1.253 into your browser and press enter. If no login screen shows up, try finding the correct IP address for your router by Searching for your router. Enter your router username. This could be admin or one of these. If you changed the username on the router and can’t remember it, try resetting your router.
192.168.1.253 – Router passwords – Router Admin Login
192.168.1.253 is an IPv4 address owned by a Private network located in a private network. Find the login and password for your device on our database.
Login Admin Username & Password
Feb 1, 2022192.168.1.253. Router Admin Passwords and Login IP 192.168.1.253. Is an IP address like Linksys, TP-Link and other manufacturers used as an access point or gateway? Firms give router admin access to this address to allow network administrators to configure their routers and networks.
Complete IP location for 192.168.1.253 located in allocated to
192.168.1.253 is part of a private IP range following the standards set by RFC 1918. Reserved IPs like 192.168.1.253 cannot be used to browse the internet. A private network must use a public IP gateway or proxy to connect internet. Router Address: 192.168.1.253.
networkd location C$(\192.168.1.253) – Microsoft Community
Network location C$(\192.168.1.253) (O:) network path was not found. Using a new dell with windows 7- I get a message: Mircosoft windows network: network path was not found. Network location(1) C$(\192.168.1.253) (O:) What does this mean? This thread is locked. You can follow the question or vote as helpful, but you cannot reply to this thread.